• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your primary protection against unauthorised entry into your home. Locks might require replacement locks for patio doors due to signs of wear and tear, or other situations like moving into a new residence or a break-in.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will allow you to purchase the correct-sized lock.

Deadbolt

If you want to ensure your door is secure against intruders, it's a good idea to install a deadbolt. The bolt extends into the strike plate that is on the doorframe when locked, making it much more difficult for burglars to gain entry through the door. A single cylinder deadbolt can be activated by keys on the exterior Replace door lock side and a thumb turn part on the interior. Deadbolts are only effective if it's installed correctly, though.

First, you'll need to find out if the door has a hole to install a deadbolt or if it has to be bored. Mark the position of the hole for the deadbolt on top of the door by using the template supplied with your lock installation kit. Use your tape measure to determine the height of the deadbolt. Then, mark the high point on the outside of the door. Use a speed square to draw straight lines across the mark you made for the bolt hole.

Then, use a power drill to bore this hole until it reaches the other side of the door. This could take a while. Then, sand the hole and the edges of the door so that it's smooth. At this stage, it's a great idea also to paint or stain your door.

Once the door is ready remove any screws that are visible on the deadbolt. This will reveal the front and back assemblies of the deadbolt as well as the bolt inside. Then, unscrew the bolt and replace it with a brand new one that is compatible with the door hardware. The bolt is often attached to a set plate that you have to remove. After this is done, you will need to cut out the space for the strike plate that is on the door frame.

If your strike plate is not aligned It's likely that the previous installer didn't mortise it correctly or a weatherstripping was installed and altered the strike position. You'll need to re-mortise the strike plate and possibly even the deadbolt itself to fix the issue. Close and lock the deadbolt when you have completed this step. Be sure the bolt extends into the strike plate and then test the key to make sure it is able to open and close smoothly.

Knob

It can make your business and home less secure when the door knob is damaged. It may also make it harder to open or close the door, making it a good idea to Replace door Lock the knob. It shouldn't take longer than 30 minutes. Make use of pliers or a screwdriver to remove any knobs or handles. Be cautious not to scratch the other components of the door.

Spray WD-40, or a different dry lubricant, on the mechanism of your door knob before you begin. This will let the new lock to slide effortlessly as you turn it. To ensure that it operates properly it is essential to select a knob and handle that match the doors you already have. If you don't have a matching doorknob, you will need to buy a replacement.

To begin the replacement process, look at the knob or handle to see what screws hold it in place. If there aren't any screws you can make use of a screwdriver and wedge it between the cover plate and the hidden screws plate and remove it.

Once you've removed the old knob, examine it for signs of rust or damage. You'll need to clean it off if you notice any scratches or dents, but you shouldn't have to do anything major if the knob is in good shape.

Now is the time to put in the new knob. It is important to first look over the two knobs to make sure that you are choosing the right one for the door. You'll need to pick one with an extender rod that locks with the rod mechanism of the other knob. Once you've positioned the new knob over the hole in the door lock replacement near me, carefully insert it into the latch.

Test the spring by pressing down on it repeatedly. The latch should then spring back up each time. Install the second knob and secure it to the rod mechanism of the first knob. Thread the long screws of the doorknob's interior through the holes for the cylinder on the exterior knob and secure it in place.

Latch

A latch is a metallic piece that extends into the door jamb to keep it closed. The latch is operated by a handle or knob on the interior of the door, or by a thumb-turn on the outside. A latch can be secured using deadbolts to prevent intrusions from piercing the glass of the door. It can also guard against the accidental or deliberate closing by animals or children. You can install a latch with either a single-cylinder or double-cylinder deadbolt depending on the level of security.

Installing a latch follows the same steps as installing a deadbolt, however, there are a few variations. To make sure that the new lock will fit first, you must measure the setback on the doorjamb using a tape measure. The setback is measured from the edge of the doorjamb all the way to the center of hole for the latch plate. A typical setback is 2 3/8 to 2 3/4 inches. If you have a higher setback, you may need to purchase a more substantial latch from a hardware shop or locksmith.

Then, you'll need to make a hole for a latch plate in the doorjamb's edge. Utilize a chisel to make the mortise for the latch. Make sure the hole's depth is sufficient for the faceplate to be flush with the doorjamb. Place the strikeplate on the floor to ensure that it's positioned correctly.

If the strike is too high, you can knock the door down or apply pressure using a tire iron or crowbar. This can also cause the doorjamb's to crack. This can be repaired by drilling a new hole through the doorjamb, then cutting the core from the old one.

Installing the new strike plate is the final step. This can be accomplished by screwing the new plate into the existing screwholes. Use wood putty then to fill in any existing screw holes or bolt holes that aren't being used. Once the putty is dry, sand it smooth for an elegant finish.

Strike

The piece of metal that connects the latch and deadbolt when the door is shut is an electric strike. It is a vital part of the lock's overall safety because it prevents the door from opening, and also provides additional resistance to force or kicking. If a door is fitted with an electronic strike, it will be opened only by an entry key and a control unit that regulates its electrical impulses.

In the past, installing an electronic strike was as simple as cutting off a part of a doorjamb, which would release the latchbolt of a cylindrical lock from the pocket inside the strike. This is a drawback in terms of the appearance of an opening, and it also exposes the keeper mechanism and latchbolt to unauthorized users.

Recently, a number of electric strike manufacturers have come up with a "No Cut" kind of strike that does not require a cutout in order to operate. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without causing damage to the faceplate of the doorjamb.

The strike is equipped with an internal ramp that lifts the keeper and latchbolt when it receives an electrical impulse from a controller or reader. The latchbolt and keeper are pushed up the ramp by the retract. When the door is shut, the deadbolt stays at a lower position and the latchbolt retracts into the keeper.

Installing an electric strike can be a simple process, especially in the case of replacing upvc door lock and handle the strike on a previous door. If you're upgrading an access control system to an electric strike, it is important to make sure that the new system is compatible. It is also necessary to ensure that the strike is properly connected to your access control system and is configured for fail-safe operation.

Upgrade your strike plates with heavy duty strike plates to prevent the entry of unauthorized persons. The plates are made of up to six screws of three inches instead of two screws of three-fourths inches. The longer screws make it more difficult for someone to break the frame and then reach inside to turn the piece that turns the thumb of a single cylinder deadbolt.